Categories
Shelf for 7 chisels. 400mm
Production of the factory of joinery and carpentry tools Petrograd
Tool cabinet 440*440*400 mm, with one door and shelf
Cabinet height 400mm,
Cabinet width - 440mm,
The depth of the cabinet is 440mm.
Attention! The manufacturer reserves the right to make design changes without prior notice to the consumer. Changes do not affect the performance and specifications of the product. The tool is not included.
Made at the PETROGRAD joinery and carpentry tools factory.
Production - (Russia)
Tool cabinet 440*440*400 mm, with three drawers
Tool cabinet 440 * 440 * 400mm, with three drawers. The plywood cabinet is designed for storing tools, fasteners, fittings or various accessories. The curbstone is made of 16mm plywood. Three identical drawers. The handles are made of oak. Internal dimensions of the box: height - 125mm, depth - 355mm, width - 355mm. External dimensions: cabinet height 440mm, width - 440mm, depth - 400mm.
Made at the PETROGRAD joinery and carpentry tools factory.
Production - (Russia)
Tool cabinet 880*440*400 mm, with two doors and one shelf
Tool cabinet 880 * 440 * 400mm, with two doors and a shelf. A plywood cabinet is designed to store tools, fittings or various accessories. The curbstone is made of 16mm plywood. With two doors and a shelf. The handles are made of oak. The height of the cabinet is 440mm, width - 880mm, depth - 400mm, height - 440mm. The curbstone has one compartment divided by a horizontal shelf.
Made at the PETROGRAD joinery and carpentry tools factory.
Production - (Russia)
Стеллаж-витрина 2000*1000*500мм
Стеллаж-витрина 2000*1000*500мм предназначена для использования в торговых и выставочных залах. Надёжная конструкция обеспечивает хороший обзор и безопасное хранение экспонатов и образцов. Разборный каркас выполнен из массива бука и покрыт отделочным маслом. Каркас собран на шиповых соединениях с дополнительным усилением болтами. Раздвижные дверцы также выполнены из стекла толщиной 4мм.
Количество полок - 5, размер поверхности - 900х400мм.
Три полки из пяти устанавливаются на полкодержатели, нагрузка на эти полки не должна превышать 10кг.
Допустимая нагрузка на полки, устанавливаемые на деревянные рамы - 20 кг.
Предусмотрена возможность устанавливать полки на разной высоте.
В боковые стойки встроены светодиодные ленточные источники света. Напряжение 220В, 50Гц.
Вес витрины около 85кг.
На заказ могут быть выполнены стеллажи любых других размеров.
Производитель оставляет за собой право вносить в конструкцию изменения, не влияющие на функциональность изделия.
Производство фабрики ПЕТРОГРАДЪ, Россия.
Tool Cabinet 835*620*230, type Esquire, beech
Шкаф инструментальный предназначен для хранения ручного столярного инструмента. Габаритные размеры 835 х 620 х 230. Толщина боковых стенок 20 мм, филенок 10мм, это позволяет закрепить на них различные держатели и кейсы для инструмента.
Используя тумбы либо подстолье в качестве основы для шкафа, можно получить удобный инструментальный комод со всем необходимым инструментом и разместить его возле рабочего верстака.
Шкаф необходимо устанавливать на ровную горизонтальную поверхность или подвешивать строго вертикально на стену.
Материал корпуса, выдвижных ящиков массив бука. Задняя стенка, полики ящичков высококачественная берёзовая фанера. Дверки, филёнки бук, матовое стекло.
Покрытие твёрдое масло для мебели Borma в два слоя.
Дверцы установлены на латунных карточных петлях, закрываются на латунный шпингалет и врезной замок.
В комплект входят держатели для стамесок, заготовки для изготовления держателей для трёх рубанков. Инструмент не входит в комплект.
Материал бук. Корпус собран на соединения выступающий «ласточкин хвост», полка врезана на сквозные выступающие шипы. Я применял такие соединения что бы подчеркнуть идею Возрождения столярного дела, что бы эта утилитарная вещь стала образцом столярного изделия, украшением мастерской. Я постарался в этом изделии воплотить идею «искусство и ремесло». Все пропорции шкафа выбраны по принципу золотого сечения с небольшими поправками в пользу функционала.
Два выдвижных ящичка под мелочёвку, полка для конструкционных рубанков, пространство ограниченное задней стенкой и боковыми стенками корпуса для вертикального размещения выглаживающих и выравнивающих рубанков. Держатели для стамесок и отвёрток на внутренней стороне дверок. Используется каждый сантиметр внутреннего пространства. Матовые стёкла в дверках можно легко заменить на витражи, кумико, старинные гравюры. Я назвал эти стёкла «окошки вдохновения» .
При проектировании шкафа вдохновлялся книгой Пола Хаслака «Основные инструменты и технологии обработки дерева», работами Майка Пековича и инструментальным шкафом Исраэль Мартин @lacabratnlaescalera (инстаграмм).
С уважением, Сергей Клейн.»
Производство - мастерская Рубанков (Россия).
Cabinet for hardware, 960*940*410 mm, beech
The cabinet is designed to store a variety of accessories, tools, consumables, etc. It has 2 rows of drawers of different sizes for storing things. Each drawer has internal removable partitions. The boxes are divided into 3 compartments.
Internal dimensions of the upper drawers: height - 50mm, depth - 313mm, width - 395mm (can be divided into 2 sections - 129 and 259mm and 3 sections by 129mm each). 16 top drawers.
Internal dimensions of the bottom drawers: height - 95mm, depth - 313mm, width - 395mm (can be divided into 2 sections - 129 and 259mm and 3 sections by 129mm each). 4 lower drawers.
The sizes of the boxes may vary.
The boxes have wooden guides. The drawer fronts have no handles. You can attach the hardware to the facade yourself. The cabinet and drawers are made of 6mm, 12mm and 18mm birch plywood. Drawer fronts - beech. Coating - oil. Overall dimensions of the cabinet with top cover and bottom plinth: length 960mm, height 940mm and depth - 410mm. Production - Rubankov workshop (Russia)
Pens are not included
Tool Cabinet 880*950*400, type 2, beech wood
Tool cabinet with dimensions 880 x 950 x 400 is designed for storing tools, consumables, etc. The outer and inner surfaces of the outer and inner doors, side and even top walls are available for placing tools. A convenient organizer for planers allows you to have them always at hand. In the lower section there are 2 drawers for small tools. The sufficient thickness of the side walls and door panels allows various tool holders and cases to be attached to them. The cabinet is made of solid beech. Doors with card hinges. The cabinet is coated with Borma tung oil. Tool holders, chisel, shavings and planer attachments and tools are not included. Production - Rubankov workshop (Russia) "
Шкафы для инструмента
Popular goods
Carving knife PETROGRAD, Finnish type, 200mm/60mm
Sharpening set PETROGRAD N3, for knives, 3 stones
Sharpening set PETROGRAD N3.Water stones. Grain size: 150, 360, 500, 1000, 1500 and 2000. Size 15х15х120mm. Abrasive grain - silicon carbide. Bundle - ceramics. Hardness I ensures minimal wear of the stone during operation. When sharpening does not overheat the steel. Does not require the use of oil. Soak in water for 2-10 minutes before use. Used for sharpening and setting bevels.
High sharpening performance, second only to diamond, is ensured by the use of silicon carbide abrasive grains, which are notable for their sharpness and brittleness. The high hardness of carbide-silicon grinding materials allows you to confidently process not only carbon steels, but also hard alloys, which is impossible on stones made of electro-alumina powders. In addition to performance, it is worth noting the extraordinary tactile sensations when sharpening a tool. Stones quickly give a slurry and produce a very pleasant sound.
> Water stones PETROGRAD are distinguished by high performance and geometry in a state of delivery.
In the characteristic of a water stone are specified: the first letter - hardness (I, J - soft, K - average); Japanese grain size according to JIS R6001-1987 is 150 (80 microns), 360 (34 microns), 500 (24 microns), 1000 (12 microns), 2000 (6 microns) and C is silicon carbide.
| 150 | 360 | 500 | 1000 | 1500 | 2000 | |
| Sharpening set PETROGRAD N3 | + | + | + | |||
| Sharpening set PETROGRAD N4 | + | + | + | + | + | + |
Comparison of FEPA, JIS and GOST standards:
Checkering layout guide / butt scribe
Checkering layout guide is necessary for confident marking of lines under the notch, for drawing notches parallel to the upper line of the forearm, for accurate drawing and repeatability of the notch pattern on both sides of the bed, for marking the edge of the guide lines with the original pattern.
Checkering layout guide is regulated along the entire length of the installation of both the upper and lower notch lines, and the length of the fixed handle is sufficient to reach the other side even through the widest trunk.
Working length of a rod is 77 mm.
Knife projection from 6.5 mm to 48.5 mm
Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.
Checkering tool complete C-1, 60°
Резец C-1, имеет 1 пирамидальный зуб. Угол вершины 90 и 60 градусов. Резец продается в сборе, имеют удобную рукоять из бука и шток с установленной на нем рабочей частью. Все резцы изготовлены из стали, прошли процесс закалки и обработки, для продолжительной и надежной работы.
Имеет V-образную форму с зубцами по обе стороны. Резец С-1 предназначен для нанесения оригинального макета рисунка, а также для углубления канавок после их нанесения, другими резцами.
Деревянная рукоятка хорошо сбалансирована и удобно лежит в руке.
На фотографии детально показаны зубцы. Обратите внимание на высокую рельефность, обеспечивающую быструю и ровную нарезку. Зубцы обеспечивает хорошее удаление всех твердых пород древесины.
Резцу все равно, что вырезать глубокие или мелкие пазы, прямые или закругленные углы, параллельные линии или перекрестную штриховку, по направлению волокна или поперек. Не нужно заново делать проход, чтобы обработать неровные участки. Ровной получается каждый элемент.
Ширина рабочей части 5 мм, длина рабочей части 11 мм, угол вершины 90 и 60 градусов.
Производство - фабрика столярных и плотницких инструментов ПЕТРОГРАДЪ.
Сделано в России
Checkering tool complete L- 9, 90°
Checkering tools from L-series have two sides: left side with teeth, right side - smooth, used as a guide. Between the tool tips, the gap is equal to the pitch. All the cutters are made of steel, underwent a process of hardening and processing, for long and reliable work. The right blade is devoid of teeth, has a sharp and smooth shape, and exactly follows along the guide line. The left blade has teeth and cuts a new groove during the process of notching from right to left. At the same time between the previous line and the new remains empty space - the line width in the usual row. Thus, it is possible to alternate sections with a notch and neat smooth lines of the same width. Such a notch principle is often called "French" or "Scottish."
Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.
Checkering tool complete N2-22, 90°
Checkering tool No2. Both sides with teeth. Used for the application of grooves and their deepening after application. One blade runs along the guideline, while the other marks the next groove. When moving to the next groove, the tool deepens it and again applies the next groove. Cutter 2 It is a combination of tools for expanding and deepening grooves. Beech handle. All the cutters are made of steel, underwent a process of hardening and processing, for long and reliable work.
Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.
| Item code | Item | Cutting angle |
Teeth per inch |
| М00015687 | N2-16 | 60° | 16 |
| М00015638 | N2-16 | 90° | 16 |
| М00015688 | N2-18 | 60° | 18 |
| М00015669 | N2-18 | 90° | 18 |
| М00015689 | N2-20 | 60° | 20 |
| М00015662 | N2-20 | 90° | 20 |
| М00015690 | N2-22 | 60° | 22 |
| М00015637 | N2-22 | 90° | 22 |
| М00015691 | N2-24 | 60° | 24 |
| М00015676 | N2-24 | 90° | 24 |
Checkering tool complete N3-22, 90°
Checkering tools from series N3, have two sides: the right side is smooth, used as a guide, the left - with teeth. All the cutters are made of steel, underwent a process of hardening and processing, for long and reliable work. The right blade is devoid of teeth, has a sharp and smooth shape, and exactly follows along the guide line. The left blade has teeth and cuts a new groove during the process of notching from right to left. Thus, it is possible to apply a notch, using the previous groove, as a guide. Beech handle.
Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.
Checkering tool complete N4-22, 90°
Checkering tools from series N4 have two sides: the right side with teeth, the left - smooth, is used as a guide. All the cutters are made of steel, underwent a process of hardening and processing, for long and reliable work. The left blade is devoid of teeth, has a sharp and smooth shape, and exactly follows along the guide line. The right blade has teeth and cuts a new groove during the process of notching from left to right. Thus, it is possible to apply a notch, using the previous groove, as a guide. Beech handle.
Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.
Checkering tool complete S-1, 60°
Checkering tool S-1 has 1 pyramidal tooth. Angle of the top is 60 degrees. The cutter has a convenient beech handle and a rod with a sharp bend perpendicular to the cutting axis and the working part installed on it. All the cutters are made of steel, undergone the process of hardening and processing, for long and reliable work.
It is V-shaped with teeth on both sides. Designed to handle corners and bends, as well as hard-to-reach places.
Pay attention to the high relief, providing fast and smooth cutting. The tines provide good removal of all hardwoods.
The cutter has not matter what cutting - deep or shallow grooves, right or rounded corners, parallel lines or cross-hatching, in the direction of the fiber or across. No need to re-do the pass to treat uneven areas. Every element is smooth and beautiful.
The width of the working part is 5 mm, the length of the working part is 5 mm, the apex angle is 60 °
Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.
Checkering tool complete T-18, 90°
Checkering tools from T-series has three cutting parts. All the cutters are made of steel, underwent a process of hardening and processing, for long and reliable work. The beech handle is well balanced and easy to use.
At the same time cut all three blades with equally spaced teeth, so you can quickly apply the pattern immediately to a large area. This speeds up the process of drawing the picture, eliminates the additional effort. The lines are parallel with a single pass.
The cutter has not matter what cutting - deep or shallow grooves, right or rounded corners, parallel lines or cross-hatching, in the direction of the fiber or across. No need to re-do the pass to treat uneven areas. Smooth turns every groove.
Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.