%

Axe handle, N18, right, 450mm

Топорища ПЕТРОГРАДЪ, N17 и N18 разработаны специально для модели топоров Плесков, для тески бревна, изготовлении лафетов. Изготовлено топорище из древесины Клёна.
Длина 450 мм размер всаживаемой части ширина максимальная 58 мм, минимальная 48 мм, толщина максимальная 27 мм,минимальная 27 мм. вес 380 г

Производство - фабрика столярных и плотницких инструментов ПЕТРОГРАДЪ.
Сделано в России.

2940p(45.22)
Отзывов: 1
Рейтинг :

Axe handle N5 385mm

Топорище ПЕТРОГРАДЪ, N5, выполнено из древесины Клёна. Длина 385мм размер всаживаемой части ширина максимальная 51,5 мм, минимальная 49 мм, толщина максимальная 22 мм,минимальная 19 мм. вес 200 г

Производство - фабрика столярных и плотницких инструментов ПЕТРОГРАДЪ.
Сделано в России

1860p(28.61)
Отзывов: 1
Рейтинг :
%

Axe handle N14 400mm

Axe handle N14 400mm, is made of Maple wood. Length 400mm, size of the inserted part: width 49mm, thickness 20mm. weight 190 g

Production - factory of joinery and carpentry tools PETROGRAD.
Made in Russia.

1860p(28.61)
Отзывов: 1
Рейтинг :
%

Axe handle, N17, left, 450mm

Топорища ПЕТРОГРАДЪ, N17 и N18 разработаны специально для модели топоров Плесков, для тески бревна, изготовлении лафетов. Изготовлено топорище из древесины Клёна.
Длина 450 мм размер всаживаемой части ширина максимальная 58 мм, минимальная 48 мм, толщина максимальная 27 мм,минимальная 27 мм. вес 380 г

Производство - фабрика столярных и плотницких инструментов ПЕТРОГРАДЪ.
Сделано в России.

2940p(45.22)
Отзывов: 1
Рейтинг :

Axe handle N2 565mm

Топорище ПЕТРОГРАДЪ, N2, выполнено из древесины Клёна. Длина 565мм размер всаживаемой части ширина максимальная 51,5 мм, минимальная 49 мм, толщина максимальная 22 мм,минимальная 20 мм. вес 290 г

Производство - фабрика столярных и плотницких инструментов ПЕТРОГРАДЪ.
Сделано в России

2400p(36.91) out of stock
Отзывов: 1
Рейтинг :

Axe handle N11 395mm

Топорище ПЕТРОГРАДЪ, N11, выполнено из древесины Клёна. Длина 395мм размер всаживаемой части ширина максимальная 51,5 мм, минимальная 49 мм, толщина максимальная 21 мм,минимальная 19 мм. вес 210 г

Производство - фабрика столярных и плотницких инструментов ПЕТРОГРАДЪ.
Сделано в России

1860p(28.61) out of stock
Отзывов: 1
Рейтинг :
%

Axe handle N13 300mm

Топорище ПЕТРОГРАДЪ, N13, выполнено из древесины Клёна. Длина 300мм размер всаживаемой части ширина максимальная 48 мм, минимальная 47 мм, толщина максимальная 21 мм,минимальная 20 мм. вес 160 г

Производство - фабрика столярных и плотницких инструментов ПЕТРОГРАДЪ.
Сделано в России

2500p(38.45)
Отзывов: 1
Рейтинг :

Axe handle N9 520mm

Топорище ПЕТРОГРАДЪ, N9, выполнено из древесины Клёна. Длина 520мм размер всаживаемой части ширина максимальная 53 мм, минимальная 52 мм, толщина максимальная 25 мм,минимальная 25мм. вес 270 г

Производство - фабрика столярных и плотницких инструментов ПЕТРОГРАДЪ.
Сделано в России

2400p(36.91) out of stock
Отзывов: 1
Рейтинг :
%

Axe handle N16 430mm

The hatchet PETROGRAD, N16, is made of Maple wood. Length 430 mm, size of the inserted part, maximum width 61 mm, minimum 61 mm, maximum thickness 32 mm, minimum 32 mm. weight 320 g

Production - factory of joinery and carpentry tools PETROGRAD.
Made in Russia

2500p(38.45)
Отзывов: 1
Рейтинг :
%

Axe handle N8 670mm

The hatchet PETROGRAD, N8, is made of Maple wood. Length 670 mm size of the inserted part maximum width 53 mm, minimum 52 mm, maximum thickness 33 mm, minimum 31 mm. weight 490 g

Production - factory of joinery and carpentry tools PETROGRAD.
Made in Russia

3200p(49.22)
Отзывов: 1
Рейтинг :
%

Axe handle N1 470mm

The hatchet PETROGRAD, N1, is made of Maple wood. Length 470 mm, size of the inserted part, width 50 mm, thickness 20 mm. weight 280 g

Production - factory of joinery and carpentry tools PETROGRAD.
Made in Russia.

2500p(38.45)
Отзывов: 1
Рейтинг :
%

Axe handle N6 480mm

Axe handle N6 480mm, is made of Maple wood. Length 480mm, size of the inserted part, width 55mm, thickness 21mm. weight 260 g

Production - factory of joinery and carpentry tools PETROGRAD.
Made in Russia.

1860p(28.61) out of stock
Отзывов: 1
Рейтинг :
new

Hornbeam axe wedge, 2 pcs

Клинья для насадки топора, граб, 2 штуки. Граб – это одна из самых твердых пород дерева. Именно клинья из граба идеально подходят для фиксации головы топора на топорище. В комплекте 2 клина. Длина составляет 75 мм, ширина – 60 мм. Производство – фабрика Петроградъ (Россия).

450p(6.92)
Отзывов: 1
Рейтинг :

Axe handle, N20, 890mm

Топорище ПЕТРОГРАДЪ, N19, выполнено из древесины Клёна. Длина 500мм размер всаживаемой трапециевидной формы. Ширина - 74 мм, толщина - 21-28мм. вес 390 г

Производство - фабрика столярных и плотницких инструментов ПЕТРОГРАДЪ.
Сделано в России

2500p(38.45)
Отзывов: 1
Рейтинг :
new

Топорище ПЕТРОГРАДЪ, N35, 810 мм

Топорище ПЕТРОГРАДЪ, N35, 810 мм. Выполнено из клёна высшего сорта. Является черновой заготовкой для изготовления топора. Рекомендуем к этому топорищу выбирать головы топоров с массой до 1200 грамм. Производство фабрика Петроградъ (Россия).
2500p(38.45)
Отзывов: 1
Рейтинг :
new

Топорище ПЕТРОГРАДЪ, N36, 320 мм, гранёное

Топорище ПЕТРОГРАДЪ, N36, 320 мм, гранёное Выполнено из ясеня высшего сорта. Является черновой заготовкой для изготовления топора. Рекомендуем к этому топорищу выбирать головы топоров с массой до 600 грамм. Производство фабрика Петроградъ (Россия).
2500p(38.45)
Отзывов: 1
Рейтинг :
new

Axe handle, N24, 710mm

Топорище ПЕТРОГРАДЪ, N24, 710 мм. Выполнено из ясеня высшего сорта. Является черновой заготовкой для изготовления топора. Рекомендуем к этому топорищу выбирать головы топоров с массой до 1800 грамм. Производство – фабрика Петроградъ (Россия).
2400p(36.91) out of stock
Отзывов: 1
Рейтинг :

Топорища ПЕТРОГРАДЪ

Carving knife PETROGRAD, Finnish type, 200mm/60mm

Carving knives with a sharp tip are designed for detailing and working in hard to reach places. Blade length 45mm or 60mm, rounded butt. A comfortable oval redwood handle is saturated with oil and covered with shellac. The length of the handle - 115mm. Excellent knife for both beginners and professionals. The 2.5 mm thick blade is made of high carbon steel hardened to a 59-61 HRc. All the cutters are sharpened and ready to go. Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.
 
2500p
Отзывов: 1
Рейтинг:

Sharpening set PETROGRAD N3, for knives, 3 stones

Sharpening set PETROGRAD N3.Water stones. Grain size: 150, 360, 500, 1000, 1500 and 2000. Size 15х15х120mm. Abrasive grain - silicon carbide. Bundle - ceramics. Hardness I ensures minimal wear of the stone during operation. When sharpening does not overheat the steel. Does not require the use of oil. Soak in water for 2-10 minutes before use. Used for sharpening and setting bevels.

High sharpening performance, second only to diamond, is ensured by the use of silicon carbide abrasive grains, which are notable for their sharpness and brittleness. The high hardness of carbide-silicon grinding materials allows you to confidently process not only carbon steels, but also hard alloys, which is impossible on stones made of electro-alumina powders. In addition to performance, it is worth noting the extraordinary tactile sensations when sharpening a tool. Stones quickly give a slurry and produce a very pleasant sound.

> Water stones PETROGRAD are distinguished by high performance and geometry in a state of delivery.
In the characteristic of a water stone are specified: the first letter - hardness (I, J - soft, K - average); Japanese grain size according to JIS R6001-1987 is 150 (80 microns), 360 (34 microns), 500 (24 microns), 1000 (12 microns), 2000 (6 microns) and C is silicon carbide.

 

  150 360 500 1000 1500 2000
Sharpening set PETROGRAD N3     + +   +
Sharpening set PETROGRAD N4 + + + + + +

 

Comparison of FEPA, JIS and GOST standards:

2900p
Отзывов: 1
Рейтинг:

Checkering layout guide / butt scribe

Checkering layout guide is necessary for confident marking of lines under the notch, for drawing notches parallel to the upper line of the forearm, for accurate drawing and repeatability of the notch pattern on both sides of the bed, for marking the edge of the guide lines with the original pattern.

Checkering layout guide is regulated along the entire length of the installation of both the upper and lower notch lines, and the length of the fixed handle is sufficient to reach the other side even through the widest trunk.

Working length of a rod is 77 mm.
Knife projection from 6.5 mm to 48.5 mm

Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.

500p
Отзывов: 1
Рейтинг:

Checkering tool complete C-1, 60°

Резец C-1, имеет 1 пирамидальный зуб. Угол вершины 90 и 60 градусов. Резец продается в сборе, имеют удобную рукоять из бука и шток с установленной на нем рабочей частью. Все резцы изготовлены из стали, прошли процесс закалки и обработки, для продолжительной и надежной работы.
Имеет V-образную форму с зубцами по обе стороны. Резец С-1 предназначен для нанесения оригинального макета рисунка, а также для углубления канавок после их нанесения, другими резцами.
Деревянная рукоятка хорошо сбалансирована и удобно лежит в руке.
На фотографии детально показаны зубцы. Обратите внимание на высокую рельефность, обеспечивающую быструю и ровную нарезку. Зубцы обеспечивает хорошее удаление всех твердых пород древесины.
Резцу все равно, что вырезать глубокие или мелкие пазы, прямые или закругленные углы, параллельные линии или перекрестную штриховку, по направлению волокна или поперек. Не нужно заново делать проход, чтобы обработать неровные участки. Ровной получается каждый элемент.

Ширина рабочей части 5 мм, длина рабочей части 11 мм, угол вершины 90 и 60 градусов.

Производство - фабрика столярных и плотницких инструментов ПЕТРОГРАДЪ.

Сделано в России

850p
Отзывов: 1
Рейтинг:

Checkering tool complete L- 9, 90°

Checkering tools from L-series have two sides: left side with teeth, right side - smooth, used as a guide. Between the tool tips, the gap is equal to the pitch. All the cutters are made of steel, underwent a process of hardening and processing, for long and reliable work. The right blade is devoid of teeth, has a sharp and smooth shape, and exactly follows along the guide line. The left blade has teeth and cuts a new groove during the process of notching from right to left. At the same time between the previous line and the new remains empty space - the line width in the usual row. Thus, it is possible to alternate sections with a notch and neat smooth lines of the same width. Such a notch principle is often called "French" or "Scottish."

Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.

850p
Отзывов: 1
Рейтинг:

Checkering tool complete N2-22, 90°

Checkering tool No2. Both sides with teeth. Used for the application of grooves and their deepening after application. One blade runs along the guideline, while the other marks the next groove. When moving to the next groove, the tool deepens it and again applies the next groove. Cutter 2 It is a combination of tools for expanding and deepening grooves. Beech handle. All the cutters are made of steel, underwent a process of hardening and processing, for long and reliable work.

Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.

Item code Item Cutting angle

Teeth per inch

М00015687 N2-16 60° 16
М00015638 N2-16 90° 16
М00015688 N2-18 60° 18
М00015669 N2-18 90° 18
М00015689 N2-20 60° 20
М00015662 N2-20 90° 20
М00015690 N2-22 60° 22
М00015637 N2-22 90° 22
М00015691 N2-24 60° 24
М00015676 N2-24 90° 24

 

 

850p
Отзывов: 1
Рейтинг:

Checkering tool complete N3-22, 90°

Checkering tools from series N3, have two sides: the right side is smooth, used as a guide, the left - with teeth. All the cutters are made of steel, underwent a process of hardening and processing, for long and reliable work. The right blade is devoid of teeth, has a sharp and smooth shape, and exactly follows along the guide line. The left blade has teeth and cuts a new groove during the process of notching from right to left. Thus, it is possible to apply a notch, using the previous groove, as a guide. Beech handle. 

Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.

850p
Отзывов: 1
Рейтинг:

Checkering tool complete N4-22, 90°

Checkering tools from series N4 have two sides: the right side with teeth, the left - smooth, is used as a guide. All the cutters are made of steel, underwent a process of hardening and processing, for long and reliable work. The left blade is devoid of teeth, has a sharp and smooth shape, and exactly follows along the guide line. The right blade has teeth and cuts a new groove during the process of notching from left to right. Thus, it is possible to apply a notch, using the previous groove, as a guide. Beech handle.

Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.

850p
Отзывов: 1
Рейтинг:

Checkering tool complete S-1, 60°

Checkering tool S-1 has 1 pyramidal tooth. Angle of the top is 60 degrees. The cutter has a convenient beech handle and a rod with a sharp bend perpendicular to the cutting axis and the working part installed on it. All the cutters are made of steel, undergone the process of hardening and processing, for long and reliable work.

It is V-shaped with teeth on both sides. Designed to handle corners and bends, as well as hard-to-reach places.

Pay attention to the high relief, providing fast and smooth cutting. The tines provide good removal of all hardwoods.

The cutter has not matter what cutting - deep or shallow grooves, right or rounded corners, parallel lines or cross-hatching, in the direction of the fiber or across. No need to re-do the pass to treat uneven areas. Every element is smooth and beautiful.

The width of the working part is 5 mm, the length of the working part is 5 mm, the apex angle is 60 °

Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.

850p
Отзывов: 1
Рейтинг:

Checkering tool complete T-18, 90°

Checkering tools from T-series has three cutting parts. All the cutters are made of steel, underwent a process of hardening and processing, for long and reliable work. The beech handle is well balanced and easy to use.

At the same time cut all three blades with equally spaced teeth, so you can quickly apply the pattern immediately to a large area. This speeds up the process of drawing the picture, eliminates the additional effort. The lines are parallel with a single pass.

The cutter has not matter what cutting - deep or shallow grooves, right or rounded corners, parallel lines or cross-hatching, in the direction of the fiber or across. No need to re-do the pass to treat uneven areas. Smooth turns every groove.

Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.

850p
Отзывов: 1
Рейтинг: