Diamond T-Bar Dresser

Diamond Dresser for Grinding wheels. Any grinding abrasive wheel loses its evenness and abrasive ability (becomes greasy). Diamond t-bar quickly solves this problem by removing some of the abrasive wheel surface to flatten the geometry of the contact point.

The work surface of diamond dresser is 14x50mm. This surface is densely covered with diamonds (aprox 36 grit). The length of the bar together with the aluminum handle is 117 mm.

Benefits of diamond T-bar by Petrograd toolworks:

  • is one of the best flatting diamond abrasives on the market.
  • high leveling ability
  • high resistance to chipping
  • square profile means no wobble

Designed for dressing abrasive wheels on ceramic bond. Best for 20-40mm width and 150-300mm in diameter. Consists of a working part and a handle attached to the working part by means of a threaded connection. The working part consists of square rolled products with dimensions 50x15x15 with nickel-diamond coating on one of the side faces of 15x50 mm in size. Material of the working part and handle ST3 GOST 380-94.

*we reserve the right to change the parameters of the product that do not affect the quality of work.

3210p(49.37)
Отзывов: 1
Рейтинг :
%

Natural lapping stone PETROGRAD, 280*150*20mm

Before using it, be sure to check the stone plane for defects (surface curvature) in 6 places.
Lapping stone made of gabbro-diabase *. It is used for lapping the soles of planers, abrasive stones and other surfaces. Has a perfectly flat surface.
When working, use only abrasives for wet sanding on a paper or self-adhesive backing. Approximate dimensions: 280x150x25mm. The error is within +/- 0.07mm per 200mm.
Rubankov production (Russia)

Gabbro-diabase is a fine-grained full-crystalline volcanic rock, which, in its chemical and mineral composition, is quite close to basalt and most often has a black color. A characteristic feature of this stone is its high hardness and significant compressive strength. One of the distinguishing features of this natural stone is its relatively low silica content (about 45-52%). The color of the mineral can vary. There are specimens that are black, dark gray and even greenish-black in color. The stone has a diabase (also called ophite) structure, which is formed by chaotically located and elongated plagioclase crystals, the entire space between which is occupied by augite.

3200p(49.22)
Отзывов: 1
Рейтинг :
%

Petrograd Steel Honing Plate 200mm*70mm*12mm

Petrograd Steel Honing Plate 200(7,8")mm*70(2,7")mm*12(0.47")mm. Precision-ground to a flatness over the entire surface, this honing plate is an excellent substrate for diamond paste. Made of dimensionally stable low-carbon steel, it will retain its flatness over a lifetime of ordinary use; unlike sharpening stones, it will never need truing.

The machining process creates a regular surface pattern, imparting a very slight texture to help capture the diamond grit without compromising overall flatness. In use, the diamond particles readily embed into the softer steel, combining to form a durable, fast-cutting abrasive surface.

2980p(45.83) 3 710 p
Отзывов: 2
Рейтинг :
new

Slurry stone, PETROGRAD, 150grit, D80*32mm

Абразив для наведения суспензии, ПЕТРОГРАДЪ, D80*23мм. Предназначен для высвобождения абразива водных заточных камней. Выпускается в двух разновидностях. Производство фабрика Петроградъ (Россия).

650p(10)
Отзывов: 1
Рейтинг :

Slurry stone, PETROGRAD, 240grit, D80*32mm

Абразив для наведения суспензии, ПЕТРОГРАДЪ, D80*23мм. Предназначен для высвобождения абразива водных заточных камней. Выпускается в двух разновидностях. Производство фабрика Петроградъ (Россия).

870p(13.38)
Отзывов: 1
Рейтинг :

Slurry stone, PETROGRAD

Abrasive for dressing grinding wheels 150mm * 25mm * 25mm. It is used to clean the stone from salting. Also serves to maintain the efficiency of the grindstone by bringing new abrasive grains to the surface of the grindstone.
Press it firmly against the abrasive disc with your hands for 30 seconds. This process does not cause excessive wear on the grindstone and can be repeated many times. This stone is for roughing. After cleaning the surface of the grinding wheel, it must be leveled with a diamond cutter.

580p(8.92)
Отзывов: 1
Рейтинг :

Petrograd Steel Honing Plate 300mm*105mm*18mm

Petrograd Steel Honing Plate 300(11,8")mm*105(4,13")mm*18(0.7")mm. Precision-ground to a flatness over the entire surface, this honing plate is an excellent substrate for diamond paste. Made of dimensionally stable low-carbon steel, it will retain its flatness over a lifetime of ordinary use; unlike sharpening stones, it will never need truing.

The machining process creates a regular surface pattern, imparting a very slight texture to help capture the diamond grit without compromising overall flatness. In use, the diamond particles readily embed into the softer steel, combining to form a durable, fast-cutting abrasive surface.

3970p(61.06) out of stock
Отзывов: 1
Рейтинг :
%

Dressing stone, PETROGRAD, 200*70*70mm

Dressing stone for cleaning sharpening water stones in the range of 500 grit and above *, also suitable for diamond stones with any grit. This stone performs well on abrasives with a hard and medium bond, not recommended for use with soft water stones. The stone grain size in the region of 3000 grit (F1000) works very efficiently **. Dressing stone is made on a very soft bond and very easy release self abrasive grains. After cleaning, the treated stone works more efficiently.

Specifications:
  • Model: Baudried 1000WE
  • Brand Petrograd
  • For cleaning water stones
  • For cleaning diamond stones and stones
  • Grain: 1000 grit / # 3000 JIS
  • 200x70x20 mm
The cleaning of a water or diamond stone or a block is carried out in several moves with dressing stone over these stones. While in work a suspension of the stone is released, the stone itself can be painted in the color of the slurry from the diamond stone or water stone. The stone must first be soaked in water. At first use, it may slightly scrape up the surface and slightly crumble selfgrain.

* may differ depending on the brand of stones
** not used for sharpening tools, only for cleaning stones
2800p(43.06) out of stock
Отзывов: 1
Рейтинг :

Выравнивающий абразив

Textile 16 pocket Tool Roll, PETROGRAD, 370*330mm, for chisels

Tool roll. Size - 370x330mm, 16 pockets. It is intended for storage of tools: cutters, chisels, knives. The maximum tool length is 300mm. Made of thick fabric - Furniture FLOCK, stitched seams.

2210p
Отзывов: 1
Рейтинг:

Petrograd Shovel Gouge 50mm

Стамеска полукруглая плотницкая Тотьма, предназначена для изготовления и зачистки продольных пазов и профилей, например при изготовлении сруба. Так же подойдет для удаления коры и декорирования поверхности на больших площадях. Рекомендована к использованию плотникам. Производство фабрика Петроградъ
14200p
Отзывов: 1
Рейтинг:

Carving knife PETROGRAD, Bogorodsky type, 200mm/60mm

Carving knives for general use, as well as for large material removal. Blade length 40mm or 60mm, rounded butt. A comfortable oval redwood handle is saturated with oil and covered with shellac. The length of the handle - 115mm. Excellent knife for both beginners and professionals. The 2.5 mm thick blade is made of high carbon steel hardened to 59-61 HRc. All the knives are sharpened and ready to go. Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.

2500p
Отзывов: 1
Рейтинг:

Carving knife PETROGRAD, Finnish type, 175mm/45mm

Carving knives with a sharp tip are designed for detailing and working in hard to reach places. Blade length 45mm or 60mm, rounded butt. A comfortable oval redwood handle is saturated with oil and covered with shellac. The length of the handle - 115mm. Excellent knife for both beginners and professionals. The 2.5 mm thick blade is made of high carbon steel hardened to a 59-61 HRc. All the cutters are sharpened and ready to go. Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.

2400p
Отзывов: 1
Рейтинг:

Heavy Duty Corner Framing Chisel, PETROGRAD, model Yelnya, 540mm/300mm, 25mm*25mm (1`)

Forged corner carpenter chisel PETROGRAD 25*25 mm with a wooden handle are designed for hard work with wood. The blade is forged manually from steel ШХ15 (USA 52100, G52986, J19965; Germany 1.3505, 100Cr6, 102Cr6) and hardened to a hardness of 58-61 HRC. With the help of machining specified exact geometry. Designed for processing and cleaning the corners of deep grooves. The handles are made of ash and crimped with two stainless rings - one to prevent splitting wood near the handle, the second to harden the back of the bar when working with a mallet or hammer. A leather pad between the chisel and the grip allows you to dampen the blows. Available in 25 mm wide. Blade length 300 mm, total length 550 mm. The guarantee of 100% quality is a small hole on the back of the chisel - a trace from the diamond cone of the device for determining the hardness. This test passes every chisel.
Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.

13900p
Отзывов: 1
Рейтинг:

Carving axe PETROGRAD, model Zvenigorod 7, handle n5

Wood carving axe Zvenigorod VII . This axe is made for artistic processing of wood, such as carving sculptures, bowl carving, dish carving and other stuff.

  • Blade width 120 mm
  • Sharpening angle - 25 degrees
  • Hardness - 55-58HRc
  • Handle lenght - 350 mm
  • Full weight - 07 kg

Carving axe Zvenigorod VII is quite small and easy to control. It's weight is about 650g, makes it maneuverable and allows you to work more accurate and precise.

The shape of the axe head was designed for carving operations where palm is resting extreamly close to axe head or even on the axe head. This design helps to exelent control of the axe even during long carving sessions. Grip above the head is used for trimming, stripping. This axe model was based on samples from museum "Rubankov" and finalized taking into account the wishes of wood carvers.

The axe head is hand forged from steel 65Г (spring steel) and hardened to 55 - 58 HRc at the cutting edge and along the entire beard, the rest part is normalized to HB280. This hardening allows you to hit the poll without the risk of creating a cracks in the metal.
Head has mounted to handle on 3 wedges, one along the head eye and two in cross section.

Cutting edge is razor sharp and ready to work out of the box. Sharpening angle - 30 degrees.

Axe handle is made of maple* and coated with Danish oil**. The hatchet handle has a longitudinal bend. In cross-section the handle has the shape of an egg, which is very convenient for good grip while carving. Handle has a hole for hanging.

Woodcarving axe Zvenigorod VII are product of Petrograd toolworks and supplied in a leather case for protection of the cutting edge and easy storage. Made in Saint-Petersburg Russia.

11200p
Отзывов: 1
Рейтинг:

Bent Gouge Rubankov, N7, 30mm

Bent Gouge Rubankov, N7, 30mm (1.8 inches)

Carving chisel "Rubankov" Bent Gouge N7, 30mm ( 1.8 inches ). Perfectly suits for volume carving and deep hollow carving. The width of the cutting edge is 30mm ( 1.8inches ). The total lenght of the gouge is 280mm (11.02inches ), blade lenght is 145mm ( 5.71inches ), the lenght of the handle is 135mm (5.31inches ). Made of alloy steel, hand forged and hardened to 59-61HRc. The comfortable and ergonomic oval handle is made of cherrywood ( may change) and coated with oil.

Gouge is sharpened, honed and fully ready to work out of the box.
This model is for hand cutting and can be used with a mallet.
Produced by PETROGRAD toolworks. ( Saint-Petersburg Russia )

5800p
Отзывов: 1
Рейтинг:
new

Carving set PETROGRAD, N10

Carving set PETROGRAD, N10
The set includes:
Carving chisel PETROGRAD, V-type, 60 degree
Carving gouge PETROGRAD, 3mm
Carving gouge PETROGRAD, 6mm
Carving gouge PETROGRAD, 8mm
Carving chisel PETROGRAD, 8mm
Textile 6 pocket Tool Roll, PETROGRAD, 360*260mm, for carving knives
Carving knife PETROGRAD, model Hatchet N1, skew, 27mm

Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.

13200p
Отзывов: 1
Рейтинг:
new

Carving set PETROGRAD, N11

Carving set PETROGRAD, N11
The set includes:
Carving chisel PETROGRAD, V-type, 60 degree
Carving gouge PETROGRAD, 3mm
Carving gouge PETROGRAD, 6mm
Carving chisel PETROGRAD, 8mm
Textile 4 pocket Tool Roll, PETROGRAD, 360*200mm
Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.
10230p
Отзывов: 1
Рейтинг:

Shallow Hook Knife, PETROGRAD, type 3, left-handed

Hook knife is used for cutting out a hollow in a wooden spoon or scoop, as well as for other similar work. Shallow hook knife N3 has a water drop profile of blade. That's making it perfectly choose for cut wooden spoons bowl. The left version of knife is designed to work with the left hand towards yourself or right hand to outside.

  • Hook knife blade made from tool steel (9ХС) and hardened up to 58-60HRC.
  • All hook cutters are sharpened and ready to go.
  • The outerside of the hook is ring-shaped and perfectly polished. Thats allow you to cut wood cleanly and smoothly without scoring.
  • The handle of the hook knife is made of maple and coated with oil*.

The right version of hook knife is designed to work with the right hand towards yourself, the left version - with the left hand towards yourself.
Made by Petrograd toolworks in Saint-Petersburg Russia.

Hook knife specifications:
Blade width: 12 mm
Blade lenght: 75 mm
Steel: 9ХС
Shape: hook
Handle grip: left-handed
Handle lenght: 160 mm
Total lenght: 235 mm
Weight: 0,1 kg
*coating may change from batch to batch
3600p
Отзывов: 1
Рейтинг: