Wooden plane PETROGRAD, Jack plane



Rating : (1)
Shipping: worldwide

14000 p (215.32)

Description

Рубанок ПЕТРОГРАДЪ, 50мм/320мм (полуфуганок). Традиционный ручной деревянный полуфуганок. Рубанки данного типа и размера предназначены в первую очередь для выравнивания небольших деревянных щитов и делянок. После выравнивания изделие выглаживается чистовым рубанком с "двойной железкой" *. Деревянный рубанок легок, изящен и прекрасно скользит по заготовкам. Рубанки марки ПЕТРОГРАДЪ изготавливаются вручную, опытными мастерами и преподавателями столярной школы Rubankov.

Рубанок оснащен красивым латунным и надежным прижимом. Такой метод фиксации ножа значительно упрощает настройку рубанка и служит значительно дольше чем обычный деревянный клин.Металлические детали рубанка производятся на фабрике Петроградъ (Россия)

  • Колодка, подошвы, рукоять рубанка выполнены из твердых пород древесины
  • Деревянные части рубанка пропитаны грунтовочным маслом - в один слой и вторым слоем покрыто маслом и воском
  • Габариты полуфуганка 325*70*160мм
  • Комплектуется одним прямым ножом

Все рубаночные ножи Петроградъ имеют клиновидный спуск с углом 0,5 градуса. Это выгодно отличает их от других рубаночных ножей, и делает их идеально подходящими для деревянных рубанков с клиновой фиксацией ножа. Рабочая сторона ножа, закалённая до твёрдости 59-61HRc, помечена небольшими точками, остающимися от проверки ножа твёрдомером. Эти точки, имеющиеся на каждом ноже, являются свидетельством проверки ножей и не влияют на работоспособность изделия.

  • Угол установки ножа - 50°
  • Нож выполнен из легированной инструментальной легированной стали.
  • Твердость рубаночного ножа 59-61HRC **
  • Длина ножа - 175мм
  • Ширина ножа - 50мм
  • Толщина ножа - от 5.5мм (у РК) до 3.5мм (у хвостовика) ***
  • Угол заточки ножа 30°

Уход и заточка ножа:

  • Нож рубанка заточен на абразивах зернистостью 1000 грит
  • Мы рекомендуем довести режущую кромку ножа на абразивах ПЕТРОГРАДЪ зернистостью 2000 и 4000 грит

Уход за колодкой рубанка****:

  • Мы рекомендуем хранить деревянные рубанки ПЕТРОГРАДЪ в условиях, не допускающих резких перепадов температур и влажности воздуха во избежание коробления деревянных колодок.
  • Необходимо периодически проверяйте геометрию деревянных колодок рубанков и, прежде всего, подошвы. При необходимости выровняйте поверхности, отстрогав или отшлифовав их.
* Двойная железка - нож с стружколомателем.
Может быть использован с шерхебельным ножом.

Share / Save Link:

Specs

Reviews

Instructions ()

Нет файлов

Publications

Recommended products

Sharpening stone PETROGRAD, 200*70*20mm, 360 grit

Abrasive water stones. Grit: 150, 360, 500, 800, 1000,1500, 2000 and 4000 grit. Size 200x70x20mm. The abrasive grain is silicon carbide. Bond - ceramics. Hardness I ensures minimal wear of the stone during work. Steel does not overheat when sharpening. Does not require oil. Soak in water for 2-10 minutes before use. Designed for sharpening steels and hard alloys. Manufactured in Russia.

1700p(215.32)
Отзывов: 1
>Рейтинг:

Sharpening stone PETROGRAD, 200*70*20mm, 800 grit

Water stones. Grain size: 150, 360, 500, 1000, 1500, 2000 and 4000 grit. Size 200*70*20mm. Abrasive grain - silicon carbide. Bundle - ceramics. Hardness I ensures minimal wear of the stone during operation. When sharpening does not overheat the steel. Does not require the use of oil. Soak in water for 2-10 minutes before use. Designed for sharpening steels and hard alloys. Made in Russia.

 

2060p(215.32)
Отзывов: 1
>Рейтинг:

Sharpening stone PETROGRAD, 200*70*20mm, 1500 grit

Water stones. Grain size: 150, 360, 500, 1000, 1500, 2000 and 4000 grit. Size 200*70*20mm. Abrasive grain - silicon carbide. Bundle - ceramics. Hardness I ensures minimal wear of the stone during operation. When sharpening does not overheat the steel. Does not require the use of oil. Soak in water for 2-10 minutes before use. Designed for sharpening steels and hard alloys. Made in Russia.

 

2440p(215.32)
Отзывов: 1
>Рейтинг:

Wooden plane PETROGRAD, Gerfschaaf type

Рубанок деревянный ПЕТРОГРАДЪ, 165мм / 30мм, голландский тип (Gerfschaaf) это классический "фартучный" рубанок, основным предназначением которого издревле была работа за пределами мастерской. Образцом для создания рубанка голландского типа стал рубанок, известный под названием Gerfschaaf и хранящийся В Музее-Мастерской Рубанков. Производство фабрика Петроградъ (Россия).

8000p(215.32)
Отзывов: 1
>Рейтинг:

Checkering tool complete C-1, 90°

Checkering tool C-1 has 1 pyramidal tooth. Angle top 90 degrees. All the cutters are made of steel, undergone the process of hardening and processing, for long and reliable work.
It is V-shaped with teeth on both sides. Checkering tool C-1 is designed for applying the original layout of the picture, as well as for deepening the grooves after their application, with other cutters.
The wooden handle is made of beech, well balanced and lies comfortably in your hand.
Pay attention to the high relief, providing fast and smooth cutting. The tines provide good removal of all hardwoods.
The cutter doesnt look like cutting - deep or shallow grooves, right or rounded corners, parallel lines or cross-hatching, in the direction of the fiber or across. No need to re-do the pass to treat uneven areas. Equal each element is obtained.

The width of the working part is 5 mm, the length of the working part is 11 mm, the apex angle 90 degrees.

Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.

850p
Отзывов: 1
Рейтинг:

Checkering tool complete N2-18, 60°

Checkering tool No2. Both sides with teeth. Used for the application of grooves and their deepening after application. One blade runs along the guideline, while the other marks the next groove. When moving to the next groove, the tool deepens it and again applies the next groove. Cutter 2 It is a combination of tools for expanding and deepening grooves. Beech handle. All the cutters are made of steel, underwent a process of hardening and processing, for long and reliable work.

Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.

 

850p
Отзывов: 1
Рейтинг:

Checkering tool complete N2-18, 90°

Checkering tool No2. Both sides with teeth. Used for the application of grooves and their deepening after application. One blade runs along the guideline, while the other marks the next groove. When moving to the next groove, the tool deepens it and again applies the next groove. Cutter 2 It is a combination of tools for expanding and deepening grooves. Beech handle. All the cutters are made of steel, underwent a process of hardening and processing, for long and reliable work.

Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.

 

850p
Отзывов: 1
Рейтинг:

Checkering tool complete N3-18, 90°

Checkering tools from series N3, have two sides: the right side is smooth, used as a guide, the left - with teeth. All the cutters are made of steel, underwent a process of hardening and processing, for long and reliable work. The right blade is devoid of teeth, has a sharp and smooth shape, and exactly follows along the guide line. The left blade has teeth and cuts a new groove during the process of notching from right to left. Thus, it is possible to apply a notch, using the previous groove, as a guide. Beech handle. 

Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.

850p
Отзывов: 1
Рейтинг:

Checkering tool complete N4-18, 90°

Checkering tools from series N4 have two sides: the right side with teeth, the left - smooth, is used as a guide. All the cutters are made of steel, underwent a process of hardening and processing, for long and reliable work. The left blade is devoid of teeth, has a sharp and smooth shape, and exactly follows along the guide line. The right blade has teeth and cuts a new groove during the process of notching from left to right. Thus, it is possible to apply a notch, using the previous groove, as a guide. Beech handle.

Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.

850p
Отзывов: 1
Рейтинг:

Checkering tool complete S-1, 90°

Checkering tool S-1 has 1 pyramidal tooth. Angle of the top is 90 degrees. The cutter has a convenient beech handle and a rod with a sharp bend perpendicular to the cutting axis and the working part installed on it. All the cutters are made of steel, undergone the process of hardening and processing, for long and reliable work.

It is V-shaped with teeth on both sides. Designed to handle corners and bends, as well as hard-to-reach places.

Pay attention to the high relief, providing fast and smooth cutting. The tines provide good removal of all hardwoods.

The cutter has not matter what cutting - deep or shallow grooves, right or rounded corners, parallel lines or cross-hatching, in the direction of the fiber or across. No need to re-do the pass to treat uneven areas. Every element is smooth and beautiful.

The width of the working part is 5 mm, the length of the working part is 5 mm, the apex angle is 90 °

Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.

850p
Отзывов: 1
Рейтинг:

Shallow Hook Knife, PETROGRAD, type 3, right-handed

Hook knife is used for cutting out a hollow in a wooden spoon or scoop, as well as for other similar work. Shallow hook knife N3 has a water drop profile of blade. That's making it perfectly choose for cut wooden spoons bowl. The right version of knife is designed to work with the right hand towards yourself or left hand to outside.

  • Knife blade width - 12mm.
  • Spoon cutter length - 235 mm
  • Handle length - 160 mm
  • Hook knife blade made from tool steel (9ХС) and hardened up to 58-60HRC.
  • All hook cutters are sharpened and ready to go.
  • The outerside of the hook is ring-shaped and perfectly polished. Thats allow you to cut wood cleanly and smoothly without scoring.
  • The handle of the hook knife is made of maple and coated with oil.

The right version of hook knife is designed to work with the right hand towards yourself, the left version - with the left hand towards yourself.
Made by Petrograd toolworks in Saint-Petersburg Russia.

3600p
Отзывов: 1
Рейтинг:

Leather Knife PETROGRAD, type 1, single stright bevel

Straight and flat leather Knife type 1 with a single bevel (up or right). This model has one flat side and one bevel side. It's simple knife for paring and skiving.

  • for straight cuts
  • for skiving
  • for paring

Flat Leather knife type 1 by Petrograd toolworks comes with a leather sheath. Edge is perfectly sharpened and ready to work out of the box.
This type of knives is used in handicraft, leather work, and shoemaking.

  • blade made of tool alloy steel 9ХФ
  • blade thickness - 1.7 mm
  • edge lenght - 40 mm
  • blade lenght - 70mm
  • handle made of wood *
  • oil covered **
2600p
Отзывов: 1
Рейтинг:

Bit for checkering tool S-1, 90°

Насадка на резец для чекеринга S-1, 90° (одна РК) имеет 1 пирамидальный зуб. Углы вершин 90 и 60 градусов. Все резцы изготовлены из стали, прошли процесс закалки и обработки. Имеют V-образную форму. Резцы S-предназначен для обработки углов и изгибов, а также труднодоступных мест. Высокая рельефность обеспечивает быструю и ровную нарезку на твердых породах древесины. Резцы могут резать, как глубокие так и мелкие пазы, прямые или закругленные углы, параллельные линии или перекрестную штриховку, по направлению волокна или поперек. Не нужно заново делать проход, чтобы обработать неровные участки. При определенных навыках ровной получается каждая канавка.

Производство - фабрика столярных и плотницких инструментов ПЕТРОГРАДЪ.

Сделано в России

570p
Отзывов: 1
Рейтинг:

Axe Anika, model Tomohawk

Топор Аника, Томагавк, с чехлом. Ультра-легкий топор Томагавк с обухом-молотком. Идеальный инструмент для передвижений налегке и хозяйственной деятельности в лесу. Заточка с микроподводом для работ по сухой и сырой древесине. Вес головы — около 600 грамм. Вес топора — около 800 грамм. Общая длина — 400-450 мм.
7900p
Отзывов: 1
Рейтинг: