%

Wooden Vise Set

The screw pair (screw + nut) for Milkman's workbench is made of hornbeam and coated with oil. Mounting screw thread diameter 25 mm - pitch 6 in. Screw length 165mm, thread length - 100mm. Rectangular wooden nut 100x40x40mm for making additional clamps, for example, small wooden vices or Moxon vices. It is better to purchase 2 screw pairs. Made in Russia.

1800p(0)
Отзывов: 1
Рейтинг :
%

PETROGRAD Workbench's hardware kit N2

Finishing oil PETROGRAD for workbenches and tool handles, 0.5l. Primer, used to apply the first coat before finishing. Recommended for use on hard or absorbent wood. Recommended for workbenches, tables, handles, woodworking tools and other woodworking parts. For indoor use only. It quickly and deeply penetrates the material and also quickly polymerizes.
Composition:
Tung oil, linseed oil, modified oils (linseed, tung, safflower, walnut), ricin oil, carnauba wax, micronized wax.
Mode of application:
Apply oil evenly to the prepared surface free of dirt and grease using a brush or lint-free cloth. After 10 minutes, wipe off the remaining oil from the surface with a dry, lint-free cloth. After 8 hours (depending on layer thickness and ambient temperature) apply a second coat. Ensure good ventilation of the room, both during application and at the end of work.
Note:
Certain oily, exotic or brightly colored woods and excessive amounts can prevent the oil from drying or greatly slow down the drying process. In this case, good ventilation is needed to speed it up.
- Do not use nitrile gloves for work.
- Safe for hands
- Always wear protective goggles when working.
Storage:
In a sealed container. It should be kept away from sources of fire and sparks.


These round bench rests are made from solid beech and easily fit into a table or workbench with a 19 mm hole. The smooth surface of the stops makes them easy to fit into the hole. Stop length 50 mm, head: Ø 30 mm, height 15 mm, body: Ø 18.5-18.8 mm, height 35 mm. Includes 4 pcs.

 

Fan gasket for bench press. Size 40x120 mm consists of 7 slats (4,5,5,5,5,5,10 mm). This simple device is designed to help prevent the vise from skewing and jamming by clamping the workpiece to one side of the vise. Just fit as many fan-shaped spacers as you need so that the thickness of the fan-shaped insert is approximately the same as the thickness of your part. When clamping parts with a thickness of more than 40 mm, it is recommended to use junk pieces of wood together with the fan to compensate for the skew. This keeps your workpiece securely in place and prevents the vise mechanism from skewing and jamming. The gaskets are made of various types of wood and have an aesthetic appearance.

Production - factory of joinery and carpentry tools PETROGRAD.

Made in Russia

2600p(0)
Отзывов: 1
Рейтинг :

Wooden handle for workbenche vices, 225mm

Handle for bench vice. Handle diameter - 28mm, length - 300mm. The handle is made of white beech without finishing. The handle is also equipped with two rubber retaining rings. End diameter - 46mm.
Production - Russia

1200p(0)
Отзывов: 1
Рейтинг :

Fan gasket for bench press

Fan gasket for bench press. Size 40x120 mm consists of 7 slats (4,5,5,5,5,5,10 mm). This simple device is designed to help prevent the vise from skewing and jamming by clamping the workpiece to one side of the vise. Just fit as many fan-shaped spacers as you need so that the thickness of the fan-shaped insert is approximately the same as the thickness of your part. When clamping parts with a thickness of more than 40 mm, it is recommended to use junk pieces of wood together with the fan to compensate for the skew. This keeps your workpiece securely in place and prevents the vise mechanism from skewing and jamming. The gaskets are made of various types of wood and have an aesthetic appearance.

Production - factory of joinery and carpentry tools PETROGRAD.

Made in Russia

1500p(0)
Отзывов: 1
Рейтинг :

Assistant for vertical wooden vice

The adjustable vertical bench stop allows you to expand the functionality of the bench. The stop serves to support the part when clamping with the main vise. The distance from the top of the workbench to the first hole is 190mm. The support is made of solid beech, covered with oil.
The support is installed on workbenches produced by the PETROGRAD factory

7200p(0)
Отзывов: 1
Рейтинг :

Hold Down Clamp, PETROGRAD, type 1

Bench hold down Clamp is  a classic and efficient way for quick fixing workpieces to workbench top. Workbench clamp by Petrograd toolworks is manually hand forged by our blacksmiths and present a high quality piece of art to make you job easy and enjoyable.

  • easy to use
  • strong and save clamp
  • extra fast clamping

To use hold down clamp you need to insert it into one of the bench holes for the stops in the workbench top and press down the workpiece. For more pressure can be used with wooden mallet.

  • max height of clamped piace  - 120 mm
  • diameter of the clamping rod is 16-17 mm
  • to use with 19 mm holes ( 3/4 inch)
  • for worbench top thick < 50 mm
  • material - forged steel
  • The size of the clamp is 290 x 200 mm. Material - steel.

Bench top camps are made by Petrograd toolworks in Saint-Petersburg Russia.

Hold down clamp Specifications:
Weight:1.08 kg
Type:hold down
Rod diameter:16-17 mm
Material:forged steel
Total lenght:290 mm
 * material of handles may changes from batch to batch.
3900p(0) out of stock
Отзывов: 1
Рейтинг :
new

Hold Down Clamp, PETROGRAD, type 2

Прижим верстачный - валет, ПЕTРОГРАДЪ, модель N2. Используется для прижима заготовок к верстачной доске верстака с минимальной толщиной < 50мм. Верстачный валет это специализированный г-образный прижим для быстрой фиксации заготовок к верстаку. Производство фабрика Петроград (Россия)

3900p(0)
Отзывов: 1
Рейтинг :
new

Wooden Hold Down Clamp, PETROGRAD, type 3

Прижим верстачный - валет, ПЕTРОГРАДЪ, модель N3, деревянный. Предназначен для фиксации заготовки на столярном верстаке с диаметром отверстий 19 мм. Выполнен из бука. Производство – фабрика Петроградъ (Россия).

1600p(0)
Отзывов: 1
Рейтинг :

Moxon vises, 380mm

Moxon vise, wooden screws. This is one of the most suitable wooden vise for making woodworking joints and especially dovetails. Jaws, handles and screws a made of wood, so you will never damage your sharp tools about it.

The vise must be installed on a workbench or other work surface such as massive table. This position is raising the workpiece to a comfortable height for sawing, marking and clear chisel cutting. The front jaw of vise is a clamping jaw. It is firmly fix the workpiece with two screws. Downside of front jaw protrudes downward for easy position vise flush to edge of surface.

  • easily and quickly attachment to surface by any fast clamp or bench clamp
  • easy vise position, flush to surface edge
  • rise worpice for comfortable work
  • max width of board for clamping - 380 mm (between screws)
  • max thickness of workpice - 30mm (jaw opening)

We make our Moxon vises from solid beech wood, so you can't damage sharp edges of your tools while working with it and if needed you can always make part of it itself.

  • vise is made of solid beech wood
  • front jaw lenght - 500 mm
  • jaw thickness - 45mm
  • width between screws - 380 mm
  • width of base plate - 100 mm
  • lenght of base plate - 545 mm

This model of vise present with wooden screws and handles ( metal screw model here ). Wooden screws can be purchased separately.

  • trapezoidal thread
  • strong and fast clamp
  • handles and screws made of hornbeam*

The Wooden Moxon vise by Petrograd toolworks was designed by Sergey Klein and was based on the early works of Anry Ruobo and Joseph Moxon. Vise have some changes from original work for more compliment work with dovetails and other woodworking joints. Moxon vise do not replace the classic workbench, but it is a devise that expands the arsenal of any master.

  • overall dimensions: 580x145x120
  • weight - 3.65 kg
  • made of soliid beech
  • oil coated

Axe Roslavl VII produced by Petrograd toolworks in Saint Petersburg Russia.

Dimensions: 580x145x120 mm
Weight: 3.65 kg
Type: for dovetailing
Jaw material: beech
Handles: wheel
Handles material: hornbeam
Screws thread: trapezoidal
Max width of board: 380 mm
Max thickness of workpice: 30 mm
* we recommend to use wax on screws for smooth and tight turning
** we reserve the right to make minor design changes to improve the vise performance.
9900p(0)
Отзывов: 1
Рейтинг :
%

Moxon vise, 550mm

Long Moxon vise, wooden screws. This is one of the most suitable wooden vise for making woodworking joints and especially dovetails on wide boards. Jaws, handles and screws a made of wood, so you will never damage your sharp tools about it.

The vise must be installed on a workbench or other work surface such as massive table. This position is raising the workpiece to a comfortable height for sawing, marking and clear chisel cutting. The front jaw of vise is a clamping jaw. It is firmly fix the workpiece with two screws. Downside of front jaw protrudes downward for easy position vise flush to edge of surface.

  • easily and quickly attachment to surface by any fast clamp or bench clamp
  • easy vise position, flush to surface edge
  • rise worpice for comfortable work
  • max width of board for clamping - 550 mm (between screws)
  • max thickness of workpice - 30mm (jaw opening)

We make our Moxon vises from solid beech wood, so you can't damage sharp edges of your tools while working with it and if needed you can always make part of it itself.

  • vise is made of solid beech wood
  • front jaw lenght - 500 mm
  • jaw thickness - 45mm
  • width between screws - 550 mm
  • width of base plate - 100 mm
  • lenght of base plate - 780 mm

This model of vise present with wooden screws and handles ( metal screw model here ). Wooden screws can be purchased separately.

  • trapezoidal thread
  • strong and fast clamp
  • handles and screws made of hornbeam*

The Wooden Moxon vise by Petrograd toolworks was designed by Sergey Klein and was based on the early works of Anry Ruobo and Joseph Moxon. Vise have some changes from original work for more compliment work with dovetails and other woodworking joints. Moxon vise do not replace the classic workbench, but it is a devise that expands the arsenal of any master.

  • overall dimensions: 780x145x120
  • weight - 4.5 kg
  • made of soliid beech
  • oil coated

Axe Roslavl VII produced by Petrograd toolworks in Saint Petersburg Russia.

Dimensions: 780x145x120 mm
Weight: 4.5 kg
Type: for dovetailing
Jaw material: beech
Handles: wheel
Handles material: hornbeam
Screws thread: trapezoidal
Max width of board: 550 mm
Max thickness of workpice: 30 mm
* we recommend to use wax on screws for smooth and tight turning
** we reserve the right to make minor design changes to improve the vise performance.
10200p(0)
Отзывов: 1
Рейтинг :
new

Упор верстачный ПЕТРОГРАДЪ, модель 3 (Planning Stop), для отверстий D19мм, 300мм

Упор верстачный ПЕТРОГРАДЪ, модель 3 (Planning Stop), для отверстий D19мм, 300мм. Выполнен из массива бука, имеет подвижные стержни, которые могут быть использованы как самостоятельные упоры. Производство – Фабрика Петроградъ (Россия).

1500p(0)
Отзывов: 1
Рейтинг :
new

Упор верстачный ПЕТРОГРАДЪ, модель 3 (Planning Stop), для отверстий D19мм, 600мм

Упор верстачный ПЕТРОГРАДЪ, модель 3 (Planning Stop), для отверстий D19мм, 600мм. Выполнен из массива бука, имеет подвижные стержни, которые могут быть использованы как самостоятельные упоры. Производство – Фабрика Петроградъ (Россия).

1800p(0)
Отзывов: 1
Рейтинг :
new

Упоры верстачные ПЕТРОГРАДЪ, модель 2, 2 штуки

Упоры верстачные ПЕТРОГРАДЪ, модель 2, 2 штуки. Предназначены для фиксации заготовке в верстаке или сборочном столе с отверстиями 19 мм. Упоры могут быть как почти полностью утоплены в верстачных отверстиях, так и выступать над поверхностю. Производство фабрика Петроградъ (Россия).

900p(0)
Отзывов: 1
Рейтинг :

Beech bench dog, 4 ps

These round bench rests are made from solid beech and easily fit into a table or workbench with a 19 mm hole. The smooth surface of the stops makes them easy to fit into the hole. Stop length 50 mm, head: Ø 30 mm, height 15 mm, body: Ø 18.5-18.8 mm, height 35 mm. Includes 4 pcs.

Production - factory of joinery and carpentry tools PETROGRAD.

Made in Russia

1400p(0)
Отзывов: 1
Рейтинг :

Фурнитура для верстаков

Carving knife PETROGRAD, Bogorodsky type, 200mm/60mm

Carving knives for general use, as well as for large material removal. Blade length 40mm or 60mm, rounded butt. A comfortable oval redwood handle is saturated with oil and covered with shellac. The length of the handle - 115mm. Excellent knife for both beginners and professionals. The 2.5 mm thick blade is made of high carbon steel hardened to 59-61 HRc. All the knives are sharpened and ready to go. Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.

2700p
Отзывов: 1
Рейтинг:

Carving knife PETROGRAD, Finnish type, 175mm/45mm

Carving knives with a sharp tip are designed for detailing and working in hard to reach places. Blade length 45mm or 60mm, rounded butt. A comfortable oval redwood handle is saturated with oil and covered with shellac. The length of the handle - 115mm. Excellent knife for both beginners and professionals. The 2.5 mm thick blade is made of high carbon steel hardened to a 59-61 HRc. All the cutters are sharpened and ready to go. Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.

2500p
Отзывов: 1
Рейтинг:

Checkering tool complete C-1, 60°

Резец C-1, имеет 1 пирамидальный зуб. Угол вершины 90 и 60 градусов. Резец продается в сборе, имеют удобную рукоять из бука и шток с установленной на нем рабочей частью. Все резцы изготовлены из стали, прошли процесс закалки и обработки, для продолжительной и надежной работы.
Имеет V-образную форму с зубцами по обе стороны. Резец С-1 предназначен для нанесения оригинального макета рисунка, а также для углубления канавок после их нанесения, другими резцами.
Деревянная рукоятка хорошо сбалансирована и удобно лежит в руке.
На фотографии детально показаны зубцы. Обратите внимание на высокую рельефность, обеспечивающую быструю и ровную нарезку. Зубцы обеспечивает хорошее удаление всех твердых пород древесины.
Резцу все равно, что вырезать глубокие или мелкие пазы, прямые или закругленные углы, параллельные линии или перекрестную штриховку, по направлению волокна или поперек. Не нужно заново делать проход, чтобы обработать неровные участки. Ровной получается каждый элемент.

Ширина рабочей части 5 мм, длина рабочей части 11 мм, угол вершины 90 и 60 градусов.

Производство - фабрика столярных и плотницких инструментов ПЕТРОГРАДЪ.

Сделано в России

900p
Отзывов: 1
Рейтинг:

Checkering tool complete C-1, 90°

Checkering tool C-1 has 1 pyramidal tooth. Angle top 90 degrees. All the cutters are made of steel, undergone the process of hardening and processing, for long and reliable work.
It is V-shaped with teeth on both sides. Checkering tool C-1 is designed for applying the original layout of the picture, as well as for deepening the grooves after their application, with other cutters.
The wooden handle is made of beech, well balanced and lies comfortably in your hand.
Pay attention to the high relief, providing fast and smooth cutting. The tines provide good removal of all hardwoods.
The cutter doesnt look like cutting - deep or shallow grooves, right or rounded corners, parallel lines or cross-hatching, in the direction of the fiber or across. No need to re-do the pass to treat uneven areas. Equal each element is obtained.

The width of the working part is 5 mm, the length of the working part is 11 mm, the apex angle 90 degrees.

Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.

900p
Отзывов: 1
Рейтинг:

Outdoor axe PETROGRAD, model Roslavl 7, scandy bevel, handle n11

Hand forged outdoor axe Roslavl VII with curved handle. Axe as a woodworking tool has superior cutting abilities, short handle and would be good choiсe for any outdoor activity like campings, spoon making, making bonfire and etc. This axe is ideal for those who want take a small axe for different ways of use when you are going out and about in the countryside. Although it is light, it can be used to fell a small or even midle tree, thanks to its handle and heavy, strong head. The axe is also excellent for delimbing a tree and making wooden stakes.

  • Total lenght is 370mm ( 14,57inch )
  • Height of axe is 140mm ( 5,51inch )
  • Lenght of cutting edge is 120mm ( 4,72inch )
  • Axe is hand forged from 65G steel (Germany 66Mn4, Ck67, USA 1066).
  • Curved cutting edge was straight sharpened.
  • Total weight of axe is 0,7kg  ( ± 0,05kg )
  • Handle lenght is 320mm ( 12,6inch) and it is made from solid mapple with right grain position.
  • The axe comes with leather case for protecting cutting edge.

Axe is well balanced and would be a good choice for a lot types of work. It will be great as outdoor axe, for small carpentry and othe woodwork projects. This is kind of universal axe for everyone.

Axe Roslavl VII produced by Petrograd toolworks in Saint Petersburg Russia.

Axe Roslavl VII Specifications:
Head weight: 0.63 kg
Full weight: 0.7 kg
Type: outdoor hatchet
Steel: 65Г
Hardness: 55-58HRc
Handle material: Ash*
Handle lenght: 320 mm
Edge: Curved
Sharpening angle: 30 degrees
Blade lenght: 120 mm
Total lenght: 370 mm
 * material of handles may changes from batch to batch.
** coating oil may changes too
13000p
Отзывов: 1
Рейтинг:
new

Spoon knife, PETROGRAD, type 1/22, left-handed

Ложкорез по дереву ПЕТРОГРАДЪ модель N1/22, это инструмент для резьбы деревянных ложек и других впуклых поверхностей. Основная задача ложкореза - выборка лунки в деревянной ложке (черпало). Выпускается двух видов: правый и левый. Производство фабрика Петроградъ (Россия)

3200p
Отзывов: 1
Рейтинг:
new

Carving knife PETROGRAD, skew type, 45 degrees

Нож для резьбы по дереву, ПЕТРОГРАДЪ, косая заточка 45град. Предназначен для широкого спектра работ. Рукоять выполнена из ясеня, угол скоса 45 градусов, инструментальная сталь. Производство фабрика Петроградъ (Россия).

2500p
Отзывов: 1
Рейтинг:

Butt chisel, PETROGRAD, model Neva, 6mm

Стамеска ПЕТРОГРАДЪ, серия Нева, 6мм. Стамески спроектированы, ориентируясь на многолетний опыт мастеров-краснодеревщиков. Форма лезвия имеет боковые скосы для работы в труднодоступных местах, например при подрезке и подчитки шиповых соединений: ласточкин хвост, шип-проушина, впол дерева, сковородней и прочие. Производятся с различной шириной полотна от 3мм до 26мм. Толщина лезвия переменная и увеличивается от режущей кромки к рукояти. Производство фабрика Петроградъ (Россия)

3300p
Отзывов: 1
Рейтинг:
new%

Outdoor axe PETROGRAD, model Roslavl X, handle

Топор кованый ПЕТРОГРАДЪ, модель Рославль 10, топорище н25. Отличается от других топоров удлиненной режущей кромкой. Благодаря этой особенности топор можно брать близким к полотну хватом и не бояться поранить руку при работе. Такой хват очень удобен при тёске и ошкуривании бревен. Удлиненная рукоять позволяет без лишних усилий рубить ветки и сучья. Производство фабрика Петроградъ (Россия).

15000p
Отзывов: 1
Рейтинг:
new

Масло камелии, KAPLEUM, Лаванда, 60 мл.

Масло камелии, KAPLEUM, Лаванда, 60 мл. Неформальная творческая группа GILDIA.PRO предлагает новый продукт, изготовленный на основе отлично зарекомендовавшего себя масла Камелии – KAPLEUM.

 

720p
Отзывов: 1
Рейтинг: