Categories
Carpenter drawknife PETROGRAD N3, half round, R60, 170mm, Russian type
A semicircle drawknife N3 with arms curved upwards will be convenient for various operations in the carpentry: precise fit of the logs to size, quick material removal, as well as a selection of recesses. Made in Saint Petersburg Russia.
- blade was forged manually
- made of tool steel 65G (Germany 66Mn4, Ck67, USA 1066)
- hardened to 55-58 HRC
- blade curvature radius - 60mm
- sharpening - lenticular.
The design of the drawknives N3, as well as it sharpening, is recommended by the Russian Carpenters Union for debarking and carpentry work on fitting logs. Other kind of carpentry work may require regrinding. Blade was fully hardened through, it allows you to repeatedly honing the blade or his fully re-grind it.
- handles are 140mm long
- made of beech and covered with oil
- length of the blade - 170mm
- blade width - 36 mm.
- Blade thickness - 6mm
- sharpening angle - 30grad
- Comes with a leather case with a clasp on the buttons.
*The sizes of the staple in the batch may vary slightly.
| Blade lengh: | 170 mm |
|---|---|
| Steel: | 65G steel |
| Shape: | semicircle |
| Handle lenght: | 140 mm |
| Weight: | 0,5 kg |
Carpenter drawknife PETROGRAD N5, Swedish type, 270mm
The forged drawknife bent in two directions has an advantage over other non-linear drawknives in convenience and control. The blade is forged manually from tool steel 65G (Germany 66Mn4, Ck67, USA 1066) and hardened to 55-58 HRC. Handles 140 mm long are made of beech and impregnated with oil. Blade length - 270 mm, width 36 mm. Blade thickness - 6 mm, sharpening angle - 30 degrees. Comes in a leather case with a clasp on the buttons. The total length of the drawknife is 650 mm. The design of the drawknives, as well as their sharpening, is recommended by the Russian Carpenters Union for debarking and carpentry work on fitting logs. Other kinds of carpentry work may require regrinding. Blade was fully hardened through, that allows you to repeatedly honing the blade or his fully re-grind it. Totally hand made at PETROGRAD factory of joinery and carpentry tools.
Made in Russia.
Carpenter drawknife PETROGRAD N10, half round, R200, 170mm
The design of the drawknives, as well as their sharpening, is recommended by the Russian Carpenters Union for debarking and carpentry work on fitting logs. Other kinds of carpentry work may require regrinding. Blade was fully hardened through, that allows you to repeatedly honing the blade or his fully re-grind it. Totally hand made at PETROGRAD factory of joinery and carpentry tools.
Carpenter drawknife PETROGRAD N10, half round, R200, 270mm
The design of the drawknives, as well as their sharpening, is recommended by the Russian Carpenters Union for debarking and carpentry work on fitting logs. Other kinds of carpentry work may require regrinding. Blade was fully hardened through, that allows you to repeatedly honing the blade or his fully re-grind it. Totally hand made at PETROGRAD factory of joinery and carpentry tools.
Carpenter drawknife PETROGRAD N11, u-shaped, with raised arms, 270mm
A flat drawknife with curved and perpendicular cutting edge with handles will be convenient for various operations both in woodworking and carpentry: precise fit of logs in size, manufacture of seats, quick material removal in joinery, etc. Handles are raised above the blade plane and allow work closely to the treated surface. The blade is forged manually from tool steel 65G (Germany 66Mn4, Ck67, USA 1066) and hardened to 55-58 HRC. Sharpening - chamfering up. Handles 140 mm long are made of beech and impregnated with oil. Blade length - 270 mm, width 36 mm. Blade thickness - 6 mm, sharpening angle - 30 degrees. Comes in a leather case with a clasp on the buttons. The design of the drawknives, as well as their sharpening, is recommended by the Russian Carpenters Union for debarking and carpentry work on fitting logs. Other kinds of carpentry work may require regrinding.Blade was fully hardened through, that allows you to repeatedly honing the blade or his fully re-grind it. Totally hand made at PETROGRAD factory of joinery and carpentry tools.
Made in Russia.
Drawknife PETROGRAD N13 (american type), 170mm
Small curved drawknife N13 is an american type of drawknives with curved blade that with handles looks like the letter "M". This kind of drawknives a good for deep cuts as well as for small fine cuts. So you can remove material in moment or make fine fitting operations. Would be good choice for making armchairs, small chairs and cabriole-style curly legs.
- hand forged blade from 9ХС steel
- hardened to 55-58 HRc
- blade bending radius - 1100 mm
- edge lenght - 170 mm
- blade width - 35 mm
- blade thickness - 5 mm
- sharpening angle - 30 degrees
A step is made on the working part of the blade to reduce the thickness of the cutting edge. This is done in order to reduce resistance when planing and for ease of sharpening.
- slightly raised handles
- faceted handles
- handles lenght - 140 mm
- handles made of beech
- oil coating
- leather case included
The handles are slightly raised above the plane of the blade and allow you to work close to the work surface. Supplied in a leather case with clasps.
Drawnkives are made by Petrograd toolworks in Saint Petersburg Russia
| Blade lengh: | 270 mm |
|---|---|
| Steel: | 9ХС steel |
| Shape: | curved, like "M" letter |
| Handle lenght: | 140 mm |
| Weight: | 0,46 kg |
Drawknife PETROGRAD N13 (american type)
Curved drawknife N13 is an american type of drawknives with curved blade that with handles looks like the letter "M". This kind of drawknives a good for deep cuts as well as for small fine cuts. So you can remove material in moment or make fine fitting operations. Would be good choice for making armchairs, Windsor chairs and cabriole-style curly legs.
- hand forged blade from 9ХС steel
- hardened to 55-58 HRc
- blade bending radius - 1100 mm
- edge lenght - 270 mm
- blade width - 35 mm
- blade thickness - 5 mm
- sharpening angle - 30 degrees
A step is made on the working part of the blade to reduce the thickness of the cutting edge. This is done in order to reduce resistance when planing and for ease of sharpening.
- slightly raised handles
- faceted handles
- handles lenght - 140 mm
- handles made of beech
- oil coating
- leather case included
The handles are slightly raised above the plane of the blade and allow you to work close to the work surface. Supplied in a leather case with clasps.
Drawnkives are made by Petrograd toolworks in Saint Petersburg Russia
| Blade lengh: | 270 mm |
|---|---|
| Steel: | 9ХС steel |
| Shape: | M |
| Handle lenght: | 140 mm |
| Weight: | 0,55 kg |
Carpenter drawknife PETROGRAD N1, Japanese type, straight, 125mm
Used to remove bark and smooth wood. Blade forged from high quality steel 65G (Germany 66Mn4, Ck67, USA 1066). The length of the cutting edge is 125 mm and the width of the blade is 40 mm. The handle is made of beech wood and covered with oil. The total length of the bracket is 880 mm. Skobel is equipped with a comfortable leather case with clasps on the buttons.
Totally hand made at PETROGRAD factory of joinery and carpentry tools.
Made in Russia
Carpenter drawknife PETROGRAD N7, for cleaning up grooves in logs (Meddragskniv)
Carpenter drawknife PETROGRAD N7, for cleaning up grooves in logs (Meddragskniv). A complete analogue of the Norwegian drawknife Meddragskniv. The thickness of the blade is 6 mm, the radius of the groove is 35 mm, the distance between the handles is 400 mm, the angle of grinding is 30 degrees. Forged, hardened 65G steel (Germany 66Mn4, Ck67, USA 1066) blade, cutting edge hardness - 55-58HRC. Total weight ~ 1.1kg. Handle length - 140mm. Handles are made of beech.
Designed for finishing the lunar groove after adze (removes the effect of scaly). The shape of the shoulder allows you to rotate it when working to grind the entire surface of the groove. Totally hand made at PETROGRAD factory of joinery and carpentry tools.
Made in Russia.
Скобель ПЕТРОГРАДЪ N14
Скобель ПЕТРОГРАДЪ N14 – это плотницкий инструмент, предназначенный для снятия коры с дерева, точной подгонки бревен в размер и для быстрого съема материала. Выкован вручную. Производство – Фабрика Петроградъ (Россия).
Плотницкие скобели
Popular goods
Carving knife PETROGRAD, Finnish type, 200mm/60mm
Sharpening set PETROGRAD N3, for knives, 3 stones
Sharpening set PETROGRAD N3.Water stones. Grain size: 150, 360, 500, 1000, 1500 and 2000. Size 15х15х120mm. Abrasive grain - silicon carbide. Bundle - ceramics. Hardness I ensures minimal wear of the stone during operation. When sharpening does not overheat the steel. Does not require the use of oil. Soak in water for 2-10 minutes before use. Used for sharpening and setting bevels.
High sharpening performance, second only to diamond, is ensured by the use of silicon carbide abrasive grains, which are notable for their sharpness and brittleness. The high hardness of carbide-silicon grinding materials allows you to confidently process not only carbon steels, but also hard alloys, which is impossible on stones made of electro-alumina powders. In addition to performance, it is worth noting the extraordinary tactile sensations when sharpening a tool. Stones quickly give a slurry and produce a very pleasant sound.
> Water stones PETROGRAD are distinguished by high performance and geometry in a state of delivery.
In the characteristic of a water stone are specified: the first letter - hardness (I, J - soft, K - average); Japanese grain size according to JIS R6001-1987 is 150 (80 microns), 360 (34 microns), 500 (24 microns), 1000 (12 microns), 2000 (6 microns) and C is silicon carbide.
| 150 | 360 | 500 | 1000 | 1500 | 2000 | |
| Sharpening set PETROGRAD N3 | + | + | + | |||
| Sharpening set PETROGRAD N4 | + | + | + | + | + | + |
Comparison of FEPA, JIS and GOST standards:
Checkering layout guide / butt scribe
Checkering layout guide is necessary for confident marking of lines under the notch, for drawing notches parallel to the upper line of the forearm, for accurate drawing and repeatability of the notch pattern on both sides of the bed, for marking the edge of the guide lines with the original pattern.
Checkering layout guide is regulated along the entire length of the installation of both the upper and lower notch lines, and the length of the fixed handle is sufficient to reach the other side even through the widest trunk.
Working length of a rod is 77 mm.
Knife projection from 6.5 mm to 48.5 mm
Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.
Checkering tool complete C-1, 60°
Резец C-1, имеет 1 пирамидальный зуб. Угол вершины 90 и 60 градусов. Резец продается в сборе, имеют удобную рукоять из бука и шток с установленной на нем рабочей частью. Все резцы изготовлены из стали, прошли процесс закалки и обработки, для продолжительной и надежной работы.
Имеет V-образную форму с зубцами по обе стороны. Резец С-1 предназначен для нанесения оригинального макета рисунка, а также для углубления канавок после их нанесения, другими резцами.
Деревянная рукоятка хорошо сбалансирована и удобно лежит в руке.
На фотографии детально показаны зубцы. Обратите внимание на высокую рельефность, обеспечивающую быструю и ровную нарезку. Зубцы обеспечивает хорошее удаление всех твердых пород древесины.
Резцу все равно, что вырезать глубокие или мелкие пазы, прямые или закругленные углы, параллельные линии или перекрестную штриховку, по направлению волокна или поперек. Не нужно заново делать проход, чтобы обработать неровные участки. Ровной получается каждый элемент.
Ширина рабочей части 5 мм, длина рабочей части 11 мм, угол вершины 90 и 60 градусов.
Производство - фабрика столярных и плотницких инструментов ПЕТРОГРАДЪ.
Сделано в России
Checkering tool complete L- 9, 90°
Checkering tools from L-series have two sides: left side with teeth, right side - smooth, used as a guide. Between the tool tips, the gap is equal to the pitch. All the cutters are made of steel, underwent a process of hardening and processing, for long and reliable work. The right blade is devoid of teeth, has a sharp and smooth shape, and exactly follows along the guide line. The left blade has teeth and cuts a new groove during the process of notching from right to left. At the same time between the previous line and the new remains empty space - the line width in the usual row. Thus, it is possible to alternate sections with a notch and neat smooth lines of the same width. Such a notch principle is often called "French" or "Scottish."
Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.
Checkering tool complete N2-22, 90°
Checkering tool No2. Both sides with teeth. Used for the application of grooves and their deepening after application. One blade runs along the guideline, while the other marks the next groove. When moving to the next groove, the tool deepens it and again applies the next groove. Cutter 2 It is a combination of tools for expanding and deepening grooves. Beech handle. All the cutters are made of steel, underwent a process of hardening and processing, for long and reliable work.
Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.
| Item code | Item | Cutting angle |
Teeth per inch |
| М00015687 | N2-16 | 60° | 16 |
| М00015638 | N2-16 | 90° | 16 |
| М00015688 | N2-18 | 60° | 18 |
| М00015669 | N2-18 | 90° | 18 |
| М00015689 | N2-20 | 60° | 20 |
| М00015662 | N2-20 | 90° | 20 |
| М00015690 | N2-22 | 60° | 22 |
| М00015637 | N2-22 | 90° | 22 |
| М00015691 | N2-24 | 60° | 24 |
| М00015676 | N2-24 | 90° | 24 |
Checkering tool complete N3-22, 90°
Checkering tools from series N3, have two sides: the right side is smooth, used as a guide, the left - with teeth. All the cutters are made of steel, underwent a process of hardening and processing, for long and reliable work. The right blade is devoid of teeth, has a sharp and smooth shape, and exactly follows along the guide line. The left blade has teeth and cuts a new groove during the process of notching from right to left. Thus, it is possible to apply a notch, using the previous groove, as a guide. Beech handle.
Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.
Checkering tool complete N4-22, 90°
Checkering tools from series N4 have two sides: the right side with teeth, the left - smooth, is used as a guide. All the cutters are made of steel, underwent a process of hardening and processing, for long and reliable work. The left blade is devoid of teeth, has a sharp and smooth shape, and exactly follows along the guide line. The right blade has teeth and cuts a new groove during the process of notching from left to right. Thus, it is possible to apply a notch, using the previous groove, as a guide. Beech handle.
Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.
Checkering tool complete S-1, 60°
Checkering tool S-1 has 1 pyramidal tooth. Angle of the top is 60 degrees. The cutter has a convenient beech handle and a rod with a sharp bend perpendicular to the cutting axis and the working part installed on it. All the cutters are made of steel, undergone the process of hardening and processing, for long and reliable work.
It is V-shaped with teeth on both sides. Designed to handle corners and bends, as well as hard-to-reach places.
Pay attention to the high relief, providing fast and smooth cutting. The tines provide good removal of all hardwoods.
The cutter has not matter what cutting - deep or shallow grooves, right or rounded corners, parallel lines or cross-hatching, in the direction of the fiber or across. No need to re-do the pass to treat uneven areas. Every element is smooth and beautiful.
The width of the working part is 5 mm, the length of the working part is 5 mm, the apex angle is 60 °
Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.
Checkering tool complete T-18, 90°
Checkering tools from T-series has three cutting parts. All the cutters are made of steel, underwent a process of hardening and processing, for long and reliable work. The beech handle is well balanced and easy to use.
At the same time cut all three blades with equally spaced teeth, so you can quickly apply the pattern immediately to a large area. This speeds up the process of drawing the picture, eliminates the additional effort. The lines are parallel with a single pass.
The cutter has not matter what cutting - deep or shallow grooves, right or rounded corners, parallel lines or cross-hatching, in the direction of the fiber or across. No need to re-do the pass to treat uneven areas. Smooth turns every groove.
Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.